// ----------------------------------------------------------------------------- // z2_demo_ice_top.v -- Palladium Z2 ICE-mode demo top // // ICE (In-Circuit Emulation) has NO software testbench: everything that runs // in the emulator must be hardware. This top therefore wraps the SAME DUT as // the SA demo (z2_demo_top) with a small synthesizable stimulus/checker FSM // that plays the role the SystemVerilog/Verilog TB played in SA mode: // // reset -> program LOAD/CMP -> read & check ID -> enable timer // -> wait for irq -> check STATUS flags -> check GPIO rotation // -> disable, W1C-clear flags, re-check -> PASS/FAIL LEDs // // Top-level pins (these are what ICE target/clock hookup sees): // clk_in design clock (from target or emulator clock configuration) // rst_n_in active-low reset // led_gpio mirrors DUT gpio_out (the rotating pattern) // led_irq mirrors DUT irq // led_done sequence finished // led_pass all hardware checks passed // led_fail a check failed (or irq timed out) // ----------------------------------------------------------------------------- `timescale 1ns/1ps module z2_demo_ice_top ( input wire clk_in, input wire rst_n_in, output wire [7:0] led_gpio, output wire led_irq, output reg led_done, output reg led_pass, output reg led_fail ); // ------------------------------------------------------------ DUT signals reg [7:0] paddr; reg psel; reg penable; reg pwrite; reg [31:0] pwdata; wire [31:0] prdata; wire pready; wire [7:0] gpio_out; wire irq; wire cmp_hit; z2_demo_top dut ( .clk (clk_in), .rst_n (rst_n_in), .paddr (paddr), .psel (psel), .penable (penable), .pwrite (pwrite), .pwdata (pwdata), .prdata (prdata), .pready (pready), .gpio_out (gpio_out), .irq (irq), .cmp_hit (cmp_hit) ); assign led_gpio = gpio_out; assign led_irq = irq; // ------------------------------------------------------------ FSM localparam ST_WAIT = 5'd0; localparam ST_WR_LOAD = 5'd1; localparam ST_WR_CMP = 5'd2; localparam ST_RD_ID = 5'd3; localparam ST_CHK_ID = 5'd4; localparam ST_WR_CTRL = 5'd5; localparam ST_WAIT_IRQ = 5'd6; localparam ST_RD_STAT = 5'd7; localparam ST_CHK_STAT = 5'd8; localparam ST_RD_GPIO = 5'd9; localparam ST_CHK_GPIO = 5'd10; localparam ST_WR_CTRL0 = 5'd11; localparam ST_WR_W1C = 5'd12; localparam ST_RD_STAT2 = 5'd13; localparam ST_CHK_STAT2= 5'd14; localparam ST_PASS = 5'd15; localparam ST_FAIL = 5'd16; reg [4:0] state; reg [15:0] wait_cnt; reg [31:0] rd_latched; // Bus drive is combinational from the state: each WR/RD state lasts // exactly one clock, which is one full transaction for this DUT // (pready is constant 1 and writes are captured on the clock edge). always @(*) begin paddr = 8'd0; pwdata = 32'd0; pwrite = 1'b0; psel = 1'b0; penable = 1'b0; case (state) ST_WR_LOAD: begin psel=1; penable=1; pwrite=1; paddr=8'h04; pwdata=32'd19; end ST_WR_CMP: begin psel=1; penable=1; pwrite=1; paddr=8'h0C; pwdata=32'd5; end ST_RD_ID: begin psel=1; penable=1; pwrite=0; paddr=8'h18; end ST_WR_CTRL: begin psel=1; penable=1; pwrite=1; paddr=8'h00; pwdata=32'd7; end ST_RD_STAT: begin psel=1; penable=1; pwrite=0; paddr=8'h10; end ST_RD_GPIO: begin psel=1; penable=1; pwrite=0; paddr=8'h14; end ST_WR_CTRL0: begin psel=1; penable=1; pwrite=1; paddr=8'h00; pwdata=32'd0; end ST_WR_W1C: begin psel=1; penable=1; pwrite=1; paddr=8'h10; pwdata=32'd3; end ST_RD_STAT2: begin psel=1; penable=1; pwrite=0; paddr=8'h10; end default: ; endcase end always @(posedge clk_in or negedge rst_n_in) begin if (!rst_n_in) begin state <= ST_WAIT; wait_cnt <= 16'd0; rd_latched <= 32'd0; led_done <= 1'b0; led_pass <= 1'b0; led_fail <= 1'b0; end else begin case (state) ST_WAIT: begin wait_cnt <= wait_cnt + 16'd1; if (wait_cnt >= 16'd7) state <= ST_WR_LOAD; end ST_WR_LOAD: state <= ST_WR_CMP; ST_WR_CMP: state <= ST_RD_ID; ST_RD_ID: begin rd_latched <= prdata; state <= ST_CHK_ID; end ST_CHK_ID: state <= (rd_latched == 32'h5A32_0001) ? ST_WR_CTRL : ST_FAIL; ST_WR_CTRL: begin wait_cnt <= 16'd0; state <= ST_WAIT_IRQ; end ST_WAIT_IRQ: begin wait_cnt <= wait_cnt + 16'd1; if (irq) state <= ST_RD_STAT; else if (wait_cnt > 16'd200) state <= ST_FAIL; // irq timeout guard end ST_RD_STAT: begin rd_latched <= prdata; state <= ST_CHK_STAT; end ST_CHK_STAT: state <= (rd_latched[1:0] == 2'b11) ? ST_RD_GPIO : ST_FAIL; ST_RD_GPIO: begin rd_latched <= prdata; state <= ST_CHK_GPIO; end ST_CHK_GPIO: state <= (rd_latched == 32'd2) ? ST_WR_CTRL0 : ST_FAIL; ST_WR_CTRL0: state <= ST_WR_W1C; ST_WR_W1C: state <= ST_RD_STAT2; ST_RD_STAT2: begin rd_latched <= prdata; state <= ST_CHK_STAT2; end ST_CHK_STAT2: state <= (rd_latched == 32'd0) ? ST_PASS : ST_FAIL; ST_PASS: begin led_done <= 1'b1; led_pass <= 1'b1; state <= ST_PASS; end ST_FAIL: begin led_done <= 1'b1; led_fail <= 1'b1; state <= ST_FAIL; end default: state <= ST_WAIT; endcase end end wire _unused = &{1'b0, pready, cmp_hit}; endmodule