// ----------------------------------------------------------------------------- // tb_z3_demo.v -- Simulation Acceleration testbench for z3_demo_top // // When compiled for Palladium SA mode: // ixcom -ua +dut+z3_demo_top -f rtl.f -f tb.f // this module runs on the host (Xcelium), driving transactions across the // Palladium InfiniBand/PCIe link to z3_demo_top which runs inside Palladium Z3. // // The testbench can also be run locally on a workstation (iverilog / xrun) // via scripts/run_local.sh without Palladium hardware. // ----------------------------------------------------------------------------- `timescale 1ns/1ps module tb_z3_demo; reg clk; reg rst_n; reg [7:0] paddr; reg psel; reg penable; reg pwrite; reg [31:0] pwdata; wire [31:0] prdata; wire pready; wire [7:0] gpio_out; wire irq; wire cmp_hit; // Instantiate DUT z3_demo_top dut ( .clk (clk), .rst_n (rst_n), .paddr (paddr), .psel (psel), .penable (penable), .pwrite (pwrite), .pwdata (pwdata), .prdata (prdata), .pready (pready), .gpio_out (gpio_out), .irq (irq), .cmp_hit (cmp_hit) ); // 100 MHz clock always #5 clk = ~clk; // APB write task task apb_write(input [7:0] addr, input [31:0] data); begin @(posedge clk); paddr <= addr; pwrite <= 1'b1; psel <= 1'b1; pwdata <= data; @(posedge clk); penable <= 1'b1; @(posedge clk); while (!pready) @(posedge clk); psel <= 1'b0; penable <= 1'b0; pwrite <= 1'b0; end endtask // APB read task task apb_read(input [7:0] addr, output [31:0] data); begin @(posedge clk); paddr <= addr; pwrite <= 1'b0; psel <= 1'b1; @(posedge clk); penable <= 1'b1; @(posedge clk); while (!pready) @(posedge clk); data = prdata; psel <= 1'b0; penable <= 1'b0; end endtask reg [31:0] rdata; integer pass_count; integer fail_count; initial begin pass_count = 0; fail_count = 0; clk = 0; rst_n = 0; paddr = 0; psel = 0; penable = 0; pwrite = 0; pwdata = 0; `ifdef LOCAL_SIM $dumpfile("sim_local/z3_demo.vcd"); $dumpvars(0, tb_z3_demo); `endif $display("=========================================================="); $display(" Palladium Z3 SA-Mode Verification Start (z3_demo_top) "); $display("=========================================================="); // Reset DUT #100; rst_n = 1; #20; // Check 1: ID Register Verification (Z3 signature 0x5A33_0001) apb_read(8'h18, rdata); if (rdata == 32'h5A33_0001) begin $display("[PASS] Check 1: Z3 ID register match (0x%08X)", rdata); pass_count = pass_count + 1; end else begin $display("[FAIL] Check 1: Z3 ID mismatch! Expected 0x5A330001, got 0x%08X", rdata); fail_count = fail_count + 1; end // Check 2: Default LOAD and COUNT value apb_read(8'h08, rdata); if (rdata == 32'd9) begin $display("[PASS] Check 2: Default COUNT is 9"); pass_count = pass_count + 1; end else begin $display("[FAIL] Check 2: Default COUNT error: 0x%08X", rdata); fail_count = fail_count + 1; end // Check 3: Configure Timer: LOAD=5, CMP=2, CTRL=(enable|irq_en|pattern_en) apb_write(8'h04, 32'd5); // LOAD = 5 apb_write(8'h0C, 32'd2); // CMP = 2 apb_write(8'h00, 32'h07); // CTRL: enable=1, irq_en=1, pattern_en=1 // Wait for timer interrupt @(posedge irq); $display("[PASS] Check 3: Timer interrupt (irq) asserted!"); pass_count = pass_count + 1; // Check 4: Status Register (timeout and cmp flags should be set) apb_read(8'h10, rdata); if ((rdata & 32'h03) == 32'h03) begin $display("[PASS] Check 4: STATUS register bits set (timeout & cmp: 0x%08X)", rdata); pass_count = pass_count + 1; end else begin $display("[FAIL] Check 4: STATUS register error: 0x%08X", rdata); fail_count = fail_count + 1; end // Check 5: Clear status (W1C) apb_write(8'h10, 32'h03); apb_read(8'h10, rdata); if ((rdata & 32'h03) == 32'h00) begin $display("[PASS] Check 5: STATUS cleared via W1C"); pass_count = pass_count + 1; end else begin $display("[FAIL] Check 5: STATUS W1C failed: 0x%08X", rdata); fail_count = fail_count + 1; end // Check 6: GPIO Rotating Pattern (0x01 -> 0x02 on first timeout) apb_read(8'h14, rdata); if (rdata[7:0] == 8'h02) begin $display("[PASS] Check 6: GPIO pattern rotated to 0x02"); pass_count = pass_count + 1; end else begin $display("[FAIL] Check 6: GPIO pattern error: 0x%02X", rdata[7:0]); fail_count = fail_count + 1; end #200; $display("=========================================================="); if (fail_count == 0) begin $display(" TEST PASSED: ALL %0d CHECKS COMPLETED ON Z3 ! ", pass_count); end else begin $display(" TEST FAILED: %0d PASSED, %0d FAILED ", pass_count, fail_count); end $display("=========================================================="); $finish; end // Safety timeout initial begin #100000; $display("[TIMEOUT] Simulation reached max time limit (watchdog)!"); $finish; end endmodule